A leading manufacturer in polyacrylamide (PAM) manufacturing
ASIAFLOC Chemical

Application of anitionic polyacrylamide (Zetag 4145 ZETAG4190) in sludge dewatering

Color
white powder
Application
water treatment
Certificate
iso9001
Place of Origin
china
Other Names
flocculant
CAS No
9003-05-8

Zetag 4145 is a kind of anionic polyacrylamide powder with 46% charge and Zetag 4190 is a kind of anionic polyacrylamide with 100% charge ,mainly used for water treatment and other applications.

Application of anitionic polyacrylamide (Zetag 4145 ZETAG4190) in sludge dewatering


Zetag 4145 is a kind of anionic polyacrylamide powder with 46% charge and Zetag 4190 is a kind of anionic polyacrylamide with 100% charge ,mainly used for water treatment and other applications.


Product Introduction:

Cationic polyacrylamide, CPAM for short, product appearance white powder particles, cationic polyacrylamide in acidic or alkaline medium were showing positive charge, it can effectively suspended particles in water with a negatively charged sewage flocculation precipitation, is a professional sludge dehydrating agent, at the same time also is very good water treatment coagulant aid, flocculating agent.

Polyacrylamide CAS No. 9003-05-8, implementation standard: GB17514-2008/GB12005. Gb APAM polyacrylamide quality assurance, product stability.

Cationic polyacrylamide model is mainly divided by ionic degree, 15/20/30/40/50/60% ionic degree, molecular weight is fixed.

Product features:

1, decolorization, sedimentation, turbidity removal effect is good.

2, mud solid liquid separation fast, high dehydration efficiency, small dosage.

Product use:

1, sludge dehydration: there will be sewage sludge generation, industrial production sewage, municipal sewage sludge, often is a hydrophilic colloid, high organic content, difficult to dehydrate, with cationic polyacrylamide, not only high dehydration efficiency, less dosage of agents, and easy to separate.

2, paper additives: paper industry, can and inorganic ions, fiber and other organic polymers electrostatic bridge effect, to enhance the physical strength and flexibility of paper, reduce fiber and cation, is a good paper reinforcement. At the same time can reduce the loss of fiber or filler, speed up water filtration, as retention aid, filter aid used in papermaking. The industrial wastewater produced in the process of paper production should also be treated with polyacrylamide.

3, sewage treatment: cationic polyacrylamide in acidic or alkaline media are positive, on the sewage with negative charge suspended particles flocculation precipitation, clarification effect is very good. Generally used for printing and dyeing factory wastewater, brewery wastewater, distillery wastewater, monosodium glutamate factory wastewater, sugar wastewater, meat products factory wastewater, beverage factory wastewater, coating wastewater and so on.


Product usage:

Polyacrylamide needs to be dissolved in water after the use of pharmaceutical solution treatment of the production process of sewage. Note that the dissolved pharmaceutical solution must be mixed evenly with sewage after use will be better. Dosage of reagent solution should be adjusted, do not overdosing at one time (overdosing will not work well).

PAM polyacrylamide dissolution and use:

1, when dissolving, choose clean and clean water, such as tap water, not production sewage. Dissolution can be done with water at room temperature without heating. The dissolution will be slow if the water temperature is lower than 5℃. The dissolution can be accelerated if the water temperature is properly raised, but the water temperature should not exceed 40℃.

2, the preparation of dissolved polyacrylamide concentration recommended 0.1-0.3%, that is, a liter of water add 1-3 grams of agents. The solution concentration follows the following principles:

(a) The dispensing tank is small, but the dosage is large, and the concentration of the dispensing agent can be appropriately raised, such as 0.3%;

Normal high molecular weight polyacrylamide solution concentration of 0.1%;

(b) It is recommended to prepare agents at a low concentration to facilitate adequate mixing of sewage and agents;

3, when dissolving the agent, we must pay attention to fully stirring until the agent is completely dissolved. No visible snowflake solid suspended substance is in the agent solution. The agent is transparent and colorless when it is completely dissolved.

4, do not use iron containers to prepare or store polyacrylamide solid agents and solution agents.



Product packaging and storage:

1, polyacrylamide product packaging uniform 25 kg/bag, plastic moisture-proof film, kraft paper bag double packaging.

2, the shelf life of the product is 2 years, need to store in a cool, ventilated and dry place, pay attention to moisture.


If you want to ask anything just fill in the form below and send us. We will contact you within 12 hours.

Write a review

FEATURED PRODUCTS

20 million molecular weight anionic polyacrylamide(magnafloc 511)--chinafloc
20 million molecular weight anionic polyacrylamide(magnafloc 511)--chinafloc

20 million molecular weight anionic polyacrylamide product price in 13,000 yuan/ton, the higher the molecular weight of ...

More >>
The anionic emulsion polyacrylamide (Magnafloc 110L) can be replaced by a CHINAFLOC EM73018
The anionic emulsion polyacrylamide (Magnafloc 110L) can be replaced by a CHINAFLOC EM73018


Magnafloc 110L is a anionic polyacrylamide emulsion with a high molecular weight. Mainly used in the field of water tr...

More >>
The anionic polyacrylamide (magnafloc 155,156) can be replaced by  ASIAFLOC A2520 and ASIAFLOC 2015
The anionic polyacrylamide (magnafloc 155,156) can be replaced by ASIAFLOC A2520 and ASIAFLOC 2015

Magnafloc 155 and Magnafloc 156 are two high and moderately molecular weight anionic polyacrylamide flocculantsupplied a...

More >>
Anionic polyacrylamide emulsion (Flopam EM430,EM533) can be replaced by a CHINAFLOC EM1018 EM3018
Anionic polyacrylamide emulsion (Flopam EM430,EM533) can be replaced by a CHINAFLOC EM1018 EM3018

Flopam EM430,EM635 These two anionic polyacrylamide emulsions from SNF, respectively have 30% and 50% hydrolysis degree ...

More >>